Kyoritsu 6011A Manual do Utilizador

MODEL６０１１AMULTI-FUNCTION TESTERINSTRUCTION MANUALKYORITSU ELECTRICAL INSTRUMENTS WORKS，LTD.

―8―The influencing variations used for calculating the operating error are denoted as follows;Temperature: 0 ℃and 35 ℃Supply voltage : 8V to 13.8V● Op

―9―LED indication of livecircuit warningLED indication of correctPolarity5．DC power source: 12.0 V, ripple content 1% orless6. Altitude up to 2000mBat

―10―4. CONTINUITY（RESISTANCE）TESTSWARNINGENSURE THAT CIRCUITS TO BE TESTED ARE NOT LIVE.DISCONNECT THE INSTRUMENT FROM THE CIRCUIT UNDER TEST BEFORE O

―11―turned to the OFF position. The memorized null value can be cancelled bydisconnecting the test leads and pushing the AUTO NULL/Uc SWITCH withthe

―12―5. INSULATION TESTSWARNINGENSURE THAT CIRCUITS TO BE TESTED ARE NOT LIVE.DISCONNECT THE INSTRUMENT FROM THE CIRCUIT UNDER TEST BEFORE OPERATING TH

―13―Fig 45．1．3 Conduction CurrentSince the insulation resistance is not infinite, a small leakage current flowsthrough the insulation between condu

―14―5．1．5 Total Leakage CurrentThe total leakage current is the sum of the capacitive, conduction and surfaceleakage current described above. Each of

―15―¡ Electronic fluorescent starter switches¡ Passive infra-red detectors (PIRs)¡ Dimmer switches¡ Touch switches¡ Delay timers¡ Power controllers¡ E

―16―Note:Insulation testing must only be undertaken on de-energised circuits.3．If the mains warning lamp lights and/or the buzzer sounds DO NOT PRESS

―17―6．When testing is complete release the test button BEFORE disconnecting thetest leads from the circuit or from the appliance. This will ensure t

1．Safe Testing... 12．Features...

―18―6. LOOP IMPEDANCE TESTSDISCONNECT THE INSTRUMENT FROM THE CIRCUIT UNDER TESTBEFORE OPERATING THE FUNCTION SWITCHTO SELECT THE LOOP TESTING RANGE S

―19―6.4 The loop impedance testWARNINGDO NOT PROCEED WITH TESTING UNLESS THE P-E AND P-NLAMPS ARE LIT TO CONFIRM THAT THE WIRING IS CORRECTLYCONNECTE

―20―Fig 96.5 Loop impedance at 3 phase equipmentIn order to test the Loop impedance at 3 phase equipment the optional OMADIEC(Model7133)

―21―Fig 10BLACK NEUTRALRED PHASEGREEN EARTH7. PROSPECTIVE SHORT CIRCUIT CURRENT（PSC）TESTSWARNINGNEVER CONNECT THIS INSTRUMENT ACROSS 2 PHASES.N EVER A

―22―8. RCD TESTSDISCONNECT THE INSTRUMENT FROM THE CIRCUIT UNDER TESTBEFORE OPERATING THE FUNCTION SWITCHTO SELECT THE RCD TEST RANGE SELECT“RCD”8.1 P

―23―8.2 What does the RCD test really do?The RCD is designed to trip out when the difference between the phase currentand the neutral current (this is

―24―4．Connect the instrument to the RCD to be tested either via a suitable socketoutlet（see fig 9）or using the OMA DIEC(Model7133) test lead set（seefi

―25―display.6．Press the phase selector switch to indicate 180™in the display and repeatthe test.7．MAKE SURE TO KEEP CLEAR OF EARTHED METAL DUR

―26―9. The external earth terminal．The external earth terminal at the ranges of Loop, PSC and RCD, the buzzerwarns that the mains earth is switched to

―27―10. GENERAL11. BATTERY REPLACEMENTWhen the display shows the low battery indication, ( ), disconnect the testleads from the instrument. Remove

―1―1. SAFE TESTINGElectricity is dangerous and can cause injury and death. Always treat it with thegreatest of respect and care. If you are not quite

―28―If this tester should fail to operate correctly, return it to your distributor statingthe exact nature of the fault. Before returning the instr

―29―14. CASE AND STRAP ASSEMBLYCorrect assembly is shown in Fig 12. By hanging the instrument round the neck,both hands will be left free for testing.

92-1530D 05-02DISTRIBUTORKyoritsu reserves the rights to change specifications or designs described inthis manual without notice and without obligatio

―2―barriers on the test leads.11．During testing it is possible that there may be a momentary degradation ofthe reading due to the presence of excessiv

―3―2. FEATURESMΩ AUTO NULL/Uc SWITCH Test Lead with IEC ConnectorLCD DISPLAYTest Lead for Continuity and Insulation TestingFig.１

―4―Model 6011A Multi-Function tester performs six functions in one instrument.1．Continuity tester2．Insulation resistance tester3．Loop impedance tester

―5―Over temperature protection Detects overheating of the internal resistor(used for loop and PSC tests) and of thecurrent control MOS FET (used for R

―6―3. SPECIFICATIONMeasurement SpecificationFunctionContinuityOpen CircuitVoltage (DC)Short CircuitCurrentRangeAccuracyGreater than 6 VGreater than200

―7―FunctionRatedVoltageMeasuring Range AccuracyVoltage Measurement-100-250V100-250V3% rdgTo prevent wrong connection of test leads and to maintain saf